Strongsikaflex&Reg 295 Uv - White - 10Oz Tube With Nozzle/Strongexterior Sealant And Direct Glazing Adhesive For Organic Glass In Marine Applications. Sikaflex&Reg-295 Uv Is A 1-Component Polyurethane Adhesive Of Paste-Like Consistency That Cures On Exposure To Atmospheric Moisture. It Is Suitable For Interior And Exterior Sealing Applications And To Bond Organic Glass In The Marine Business. Sikaflex&Reg-295 Uv Meets The Requirements Set Out By The International Maritime Organization (Imo). &Nbspstrongfeaturesstrongulliexcellent Application Properties/Liliresistant To Aging And Weathering/Lilisuitable For Organic Glasses/Li/Ulstrongareas Of Application/Strongsikaflex&Reg-295 Uv Has Been Specially Developed For The Marine Industry, Where It Is Used To Bond And Seal Plastic Glazing Materials In Boats And Ships. Because Of Its Excellent Weatherability This Product Can Also Be Used To Seal Joints In Exposed Areas. Suitable Substrates Are Aluminum (Bright Or Anodized), Grp (Polyester Resin), Stainless Steel, Timber, 2-Component Coatings, And Plastic Glazing Materials (Pc, Pmma). Seek Manufacturer&Rsquos Advice And Perform Tests On Original Substrates Before Using Sikaflex&Reg-295 Uv On Materials Prone To Stress Cracking. This Product Is Suitable For Experienced Professional Users Only. Tests With Actual Substrates And Conditions Have To Be Performed To Ensure Adhesion And Material Compatibility.Strongproduct Benefitsstrongulliexcellent Application Properties/Liliresistant To Aging And Weathering/Lilisuitable For Organic Glasses/Liliapproved For The Oem Market/Liliwheelmark Approved/Li/Ulstrongsurface Preparationstrongsurfaces Must Be Clean, Dry, And Free From Grease, Oil, Dust, And Contaminants. Surface Treatment Depends On The Specific Nature Of The Substrates And Is Crucial For A Long-Lasting Bond. Suggestions For Surface Preparation May Be Found On The Current Edition Of The Appropriate Sika&Reg Pre-Treatment Chart. Consider That These Suggestions Are Based On Experience And Have In Any Case To Be Verified By Tests On Original Substrates.&Nbspstrongapplicationstrongsikaflex&Reg-295 Uv Can Be Processed Between 10 &Degc And 35 &Degc (Climate And Product) But Changes In Reactivity And Application Properties Have To Be Considered. The Optimum Temperature For Substrate And Sealant Is Between 15 &Degc And 25 &Degc.Brconsider That The Viscosity Will Increase At Low Temperatures. For Easy Application, Condition The Adhesive At Ambient Temperature Prior To Use. To Ensure A Uniform Thickness Of The Bonding It Is Recommended To Apply The Adhesive In Form Of A Triangular Bead.Strongtooling &Amp Finishing/Strongtooling And Finishing Must Be Carried Out Within The Skin Time Of The Product. It Is Recommended To Use Sika&Reg Tooling Agent N. Other Finishing Agents Must Be Tested For Suitability And Compatibility Prior To The Use.&Nbspstrongremoval/Stronguncured Sikaflex&Reg-295 Uv Can Be Removed From Tools And Equipment With Sika&Reg Remover-208 Or Another Suitable Solvent. Once Cured, The Material Can Only Be Removed Mechanically. Hands And Exposed Skin Have To Be Washed Immediately Using Sika&Reg Cleaner-350H Cleaning Towels Or A Suitable Industrial Hand Cleaner And Water. Do Not Use Solvents On The Skin.Strongoverpainting/Strongsikaflex&Reg-295 Uv Can Be Painted Prior To And After The Formation Of The Skin. If The Painting Process Takes Place After The Sealant Has Built A Skin, Adhesion Could Be Improved By Treating The Joint Surface With Sika&Reg Aktivator-100 Or Sika&Reg Aktivator-205 Prior To The Painting Process. If The Paint Requires A Baking Process ( 80 &Degc), The Best Performance Is Achieved By Allowing The Sealant To Fully Cure First. All Paints Have To Be Tested By Carrying Preliminary Trials Under Manufacturing Conditions. The Elasticity Of Paints Is Usually Lower Than That Of Sealants. This Could Lead To Cracking Of The Paint In The Joint Area. !